Omron K8DT-AS/AW 单相电流继电器可检测电动机和其他设备电流变化过程中的错误。
通过继电器监测交流或直流电流。
与商用提供的电流变压器一起使用
宽度为 17.5 mm,降低面板中所需的空间。
推入式接线端子可降低布线工作。
双插入孔用于跨接布线(所有接线端子)。
K8DT-AS 可用于过电流或欠电流模式。
K8DT-AW 可同时监测过电流和欠电流
• Downsize control panels.
• Reduced wiring.
• Detects errors in Motors and other equipment via current changes.
• Use in either over current or under current mode.
• Function as an alarm.
• Set threshold values.
• Alarm output can be set as a relay or transistor output.
• Input signal – Voltage, current, water level electrode and temperature (thermocouple or platinum resistance thermometer) can be input.
• Lower power consumption.
• Long term contact reliability.
• Reliable in poor noise environments.
• Slim profile 17.5 mm
• Current Monitoring Relay.
• Single phase.
• SPDT Contact output.
• Power supply 24 V ac/dc.
• Setting range 2 to 20 mA ac/dc, 10 to 100 mA ac/dc, 50 to 500 mA ac/dc.
• Direct input.
• If using other current transformers Do Not exceed the overload capacity.
• Power supply 100 to 240 V ac, 50/60 Hz, 24 V dc
• Manual/ Automatic reset (switchable)
• Manual reset – Turn OFF the power supply for minimum of 1 sec.
• Start-up lock time 0 to 30 s.
• Green LED Power (PWR)
• Yellow LED output (OUT)
• Red LED Relay output (ALM)
• One SPDT contact relay, switchable normally closed (NC) and normally open (NO) using DIP switch.
• DIN Rail Mounted
• Weight 100 g
• Case material PC, UL 94 V-0.
• Colour N1.5
• Protection IP20 (terminals)
A monitoring / measuring relay is a protective control device, various types are available suiting what you wish to monitor. The relays receive input signals then monitor them and then output an alarm signal when a set value is reached (alarm relays). The relays protect your equipment against over voltage and over current faults. Monitoring relays monitor AC power supplies, voltage and current, analogue signals detecting unusual activity in equipment against set alarm thresholds.
• Motor protection relays
• Temperature monitoring relays
• Water level control relays
• Voltage
• Current
EN 60947-5-1, UL 60947-5-1, IP 20 Terminals
Omron K8DT 测试和监控继电器是面板理念价值设计的一部分,该理念可控制面板设计,并使制造符合全新标准。 K8DT 系列可保护重要设备使用各种符合国际安全标准的测量和监控继电器时免受伤害。 低功耗和低热量设计可提供更长的工作寿命。
K8DT 系列通过降低布线管道和顶板空间之间的宽度,有助于缩小控制面板尺寸。 细长型主体使空间内可以安装更多与控制面板同等大小的设备,从而增加控制面板的功能。
所有 K8DT 继电器上的推入式接线端子块可减少布线所需的时间和工作量。 推入式接线端子使得无需工具也可插入带引脚接线端子的固态和绞合电线或套圈。
属性 | 数值 |
---|---|
监测应用 | 电流 |
触点配置 | 单刀双掷 |
电气相位 | 1 |
电流灵敏度 | 过载电流,低电流 |
最小电流感应 | 2 mA, 10 mA, 20mA |
最大电流感应 | 20 mA, 100 mA, 500mA |
延时 | 250ms |
系列 | K8DT-AS |
安装类型 | DIN 导轨 |